Cannabis Cultivation Network

Learn How To Grow Top Shelf Medicine at Home

Register Ask Question

My grow setup and instructions, ** New Diagram **

MooseBluemane

Active Member
130
235
43
Thread starter #1
Hi gang,

So I ended up getting a seed from my provider ( Hybrid P1) and decided cool i can try to grow it. So i stuck it in soil and waited.
Yes yes, I just started and didn't have a slightest clue what i was doing.
Google is my friend.
Fast forward many months and we have the two pictures below of my grow setup.

Dimensions - 6 ft tall, interior diameter Room 1 38 x 38, Int. Dia. Room2 32 x 38

Room 1 is my veg room with 1 soon to be 2 Phizon 600 watt V/F switch and two small fans to circulate air, one top and one bottom-ish.
Room 2 is my flower room with a Vipra Spectra 300 watt, and i just ordered a 600 watt for that room to bring it up to 900 watts for flower room
I will only be flowering one at a time, as we in canada can have only 4 plants, and only 1 flowering at a time.

The room was very simple to make, the frame is 2 x 2 and reinforced by 90 metal brackets for all the corners and joint spots.
Then i got the 4 x 8 ' sheets of 1 inch styrofoam with green one side, and mylar reflective material on the other ( Home Depot)
I wired two power bars, one for each room, then sized, cut and placed the foam securing with screws and washers,
if not the screws go right thru the foam.
I got this tape from Canadian Tire that is metallic reflective plastic tape pretty cheap per roll compared to the metal duct stuff
I sealed both rooms almost air tight, No i do not plan on CO2 system

I made two doors as you see in the picture and made hinges with good old duct tape, and then some reflect tape over it
I ordered two 4 " carbon filter fan kits from amazon with speed controllers built in. One for each room, and then i will be
exhausting the filters to the outside and on that same panel in the window will be a 4 " intake and will split off and
give each room fresh air, i have ducting cut at the bottom of the rooms to bring in the air.
I will control temp via the speed of the filter fans.

That's is my plan, i have no clue what i am doing but giving it a good go. I am glad i found this spot, i think i will like it here.
 

Attachments

MooseBluemane

Active Member
130
235
43
Thread starter #8
Two pieces of pine molding sandwhiching the insultation of the door, secured by washes and nut and bolts.

Sorry forgot that instruction. If anyone has issues, or would like to build one, just ask here and ill try to help as best as i can.
 

MooseBluemane

Active Member
130
235
43
Thread starter #13
Finished the cold air intakes and connected them to outside. I used 4 inch couplers between the walls of the cabin, I ran out for one air intake so i improvised with a 2 litre plastic bottle middle section, cut down one end, and used that, you will see in one of the pictures.
20181030_130049_HDR.jpg 20181030_125003_HDR.jpg 20181030_123343_HDR.jpg 20181030_115452_HDR.jpg 20181030_115442.jpg
 

Sunshine

Organic Fanatic
2,421
4,079
113
#14
Finished the cold air intakes and connected them to outside. I used 4 inch couplers between the walls of the cabin, I ran out for one air intake so i improvised with a 2 litre plastic bottle middle section, cut down one end, and used that, you will see in one of the pictures.
View attachment 5928 View attachment 5929 View attachment 5930 View attachment 5931 View attachment 5932
Looks nice and clean @MooseBluemane! Can't wait til they're full of sticky flowers 🌻
 

MooseBluemane

Active Member
130
235
43
Thread starter #16
Almost finished the doors, need some longer bolts, but other than that, they latch nicely. I used magnetic cabinet latches
on top and bottom and use double sided foam tape to secure the wood onto the door

20181031_101823.jpg 20181031_135959.jpg 20181031_140010.jpg 20181031_140015.jpg
 

MooseBluemane

Active Member
130
235
43
Thread starter #17
I just had an idea. I put this together with some threaded rod and nuts i have for another project. Oh and some metal fishing leads as well from the Dollar Store. One pulley and pull the same time now. Also the Orange String hanging from the one of them is 24 " from bottom of light to the end. Just happens to be my optimal growing distance for those lights. My other lights are set at 18 "
20181101_155124_HDR.jpg
 
Top